SCREW AIR COMPRESSOR
Model: 15/10Y
This unit combines an air-cooled screw air end, an inverter drive, a refrigerated air dryer, five stages of precision filtration and an air receiver tank in one package. The PLC control system and the inverter work together to match motor output to your actual air demand, so the compressor does not run at full power when your workshop does not need it.It suits steel fabrication shops, metalworking facilities, woodworking and furniture factories, joinery workshops and general manufacturing plants that need clean, dry and stable compressed air.
| TECHNICAL SPECIFICATIONS | UNIT | XV-37/16YX |
|---|---|---|
| Air cooling way | - | Wind cooling |
| Exhaust volume | ³/min | 2.0 m³/min |
| Exhaust pressure | MPa | 1.50 |
| Safety value pressure | MPa | Compressor exhaust pressure +0.1 |
| Temperature | ℃ | 20 |
| Relative humidity | % | 60 |
| Heat at constant pressure | - | 1.4 |
| Environment temperature | - | 2℃-45℃ |
| Rear-cooler outlet temperature | - | ≤ Environment temperature +15℃ |
| Driving mode | - | Direct connection |
| Exhaust control | - | Capacity control |
| Unit noise | dB(A) | ≤70 |
| Unit vibration | mm/s | ≤7 |
| Gas content at the gas outlet | ppm | 0.01 |
| Exhaust dust-containing particles | - | 0.01 |
| Power of the main motor | kw | 15 |
| Motor speed | rpm | 3600 |
| Electric source | - | 380V/50HZ |
| Insulation grade of the main motor | - | F Level |
| Main motor weight | kg | 50 |
| Power line | mm² | 10 |
| Ground lead | mm² | 4 |
| Disconnect switch | A | 40 |
| Air end model number | - | DLG7V |
| Yin and Yang rotor type line | - | The third generation A type, Asymmetric 5:6 tooth shape |
| Air Dryer Model | - | HT-01G |
| Pressure | MPa(a) | 1.0 |
| Handling capacity | ㎡/min | 2.0 |
| Supply voltage | - | 220V/50HZ |
| Power | kW | 0.37 |
| Absorption dryer model | - | HT-036 |
| Pressure | MPa(a) | 1.6 |
| Handling capacity | ㎡/min | 6.7 |
| Supply voltage | - | 220V/ 50HZ-60HZ |
| Air tank | Litre | 1000 |
| Filter | - | GX02 X 5sets (W/M/H/S/X) |
| Unit weight | kg | 550 |
| External dimensions | mm | L= 2130 x W=820 x H=1980 |
Air Tank

Air Tank
With 1000L maximum capacity to give a larger air reserve. This steadies line pressure when several tools or machines draw air at once. The compressor cycles less often, so it wears less and uses less energy, and your production output stays consistent..
Filter Set

Filter Set
A multi-stage filter set removes oil aerosols, particles and moisture droplets from the compressed air. Downstream pneumatic tools, CNC auxiliaries and finishing equipment receive clean air. That means less wear, fewer breakdowns and more consistent coating and finishing quality.
Air Dryer

Air Dryer
The integrated dryer takes moisture out of the compressed air before it reaches your lines. This prevents corrosion in pipework and tools and avoids water contamination in spraying and finishing. You spend less on repairs and rework.
PLC Controller

PLC Controller
A programmable logic controller manages start/stop, pressure control and fault protection automatically. Operators see running status and alarms at a glance. It cuts manual supervision, supports safe unattended running and makes faults quicker to diagnose.
Servo Motor

Servo Motor
A servo-driven motor responds precisely to demand, holding pressure and speed tightly. It delivers accurate output with less energy wasted at partial load. You get a steadier air supply and lower power bills.
Automatic Water Drainage

Automatic Water Drainage
Condensate is drained automatically from the tank and dryer at set intervals. This stops water building up, which protects the tank from internal corrosion and keeps moisture out of your air lines.
Inverter System

Inverter System
The inverter adjusts motor speed to match actual air consumption and gives a smooth, low-inrush start. This reduces electrical stress, saves energy at part load and protects the motor and electrical network.
Air-cooled Fan

Air-cooled Fan
It keeps operating temperatures within limits in hot workshop conditions, so output stays reliable through summer.
Main Component Configuration
| TECHNICAL SPECIFICATIONS | 15/10Y |
|---|---|
| Permanent magnet synchronous motor | Zhongyan/Suma |
| Air end | Baosi |
| Radiator | Wuxilingsheng |
| Fan | Xingyi |
| Oil and gas barrels | Jiushu/Jucai |
| Controller | Purta |
| Intake valve | Hongxing/Chenan |
| Minimum pressure valve | Hongxing/Chenan |
| Oil consideration seat | Hongxing/Chenan |
| Air filter assembly | Hanman |
| Oil filter | Yaou |
| Built-in oil points | Shuangjian |
| Inverter | Purta |
| Safety valve | Fuchao |
| The screw oil | Total |
| Pressure pickup | Taji |
| Temperature sensor | Taji |
| Contactor | Schneider/Tengen |
| Filter | Huitongxinda |
| Air dry | Zhongxing/Ruitai |
| Absorption dryer | Huitongxinda |
Closer look of the machine
MACHINE GALLERY



AIR COMPRESSOR
Structure and Characteristics
Direct-Drive Power Transmission
Less power is lost in transmission, and there are fewer wearing parts to inspect or replace.
High-Efficiency Asymmetric Screw Air End
The profile compresses air efficiently and is built for long continuous duty.
Clean, Dry Compressed Air
Pneumatic tools, CNC auxiliaries and finishing equipment run with less wear, and paint and coating results stay consistent.
Built-In Air Tank
Machines get steady pressure so output quality holds up and the compressor cycles less often.
Quiet, Low-Vibration Operation
The compressor can sit close to production areas without the noise and shaking of older equipment.
Built for Hot-Climate Operation
It handles high workshop temperatures without a water-cooling circuit, and demand-matched capacity control adjusts output to air consumption.
Our Global Manufacturing Partners
TRUSTED BY INDUSTRY LEADERS





















Request a Quote
Or speak to our engineers for tailored recommendation, layout study and specifications
Reach out today
Whether you're establishing a new factory or expanding an existing production line, we are your trusted industrial equipment partner.
- mk1@mktrd-uae.com
- +97165366610
- +971565092554
- 2nd Industrial St, Industrial Area 3, Ananas Bldg. Sharjah, UAE
